VisualTarget Installation Guide

Public Channel / Installation Guides

Guided instructions on how to install the various VisualTarget mounts as well as the install of the tablets in the enclosures.
***NOTE: VisualTarget Enclosures do not support off-the-shelf RJ-45 connectors that have a rubber strain relief after the connector. The cable must be terminated with a standard RJ-45 plug.

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select page to start with

2.

1. V isualTarget INSTALLATION INSTRUCTIONS BY VisualTarget

4. ENCLOSURES V isual T arget LIGHTED ENCLOSURES 1

13. ENCLOSURES V isual T arget SLIM ENCLOSURES 2

43. Not Working? Answers at: support.magtarget.com or [email protected]

17. 3 PREFERRED MOUNTING METHODS SIDE-MOUNT

25. PREFERRED MOUNTING METHODS REAR-OFFSET MOUNT 4

33. PREFERRED MOUNTING METHODS SURFACE MOUNT 5

18. 16 For up to date guides and more see support.magtarget.com BY VisualTarget The instructions below highlight our recommended installation method for side mounting options suitable for every version of VisualTarget enclosure. Follow this guide when fastening VisualTarget enclosures to aluminum extrusions such as in door frame/mullion.

10. BY VisualTarget 8 For up to date guides and more see support.magtarget.com Note: Press the plastic cap inward if it is offset from the front enclosure.

24. 22 For up to date guides and more see support.magtarget.com BY VisualTarget This complete the installation of the MagTarget VisualTarget enclosure (side). Lighted VisualTarget Enclosure is shown here, but other types of enclosures can be installed using the same methods.

26. 24 For up to date guides and more see support.magtarget.com BY VisualTarget The instructions below highlight our recommended installation method for rear-offset mounting options suitable for every version of VisualTarget enclosure. Follow this guide when fastening VisualTarget enclosures to aluminum extrusions such as in door frame/mullion.

40. 5 PREFERRED MOUNTING METHODS GLASS MOUNT 6

32. 30 For up to date guides and more see support.magtarget.com BY VisualTarget This complete the installation of the MagTarget VisualTarget enclosure (rear-offset). Lighted VisualTarget Enclosure is shown here, but other types of enclosures can be installed using the same methods.

34. 32 For up to date guides and more see support.magtarget.com BY VisualTarget The instructions below highlight our recommended installation method for the VisualTarget Surface Mount.

6. BY VisualTarget 4 For up to date guides and more see support.magtarget.com Step 2: Plug the VisualTarget lightning connector into the device.

8. BY VisualTarget 6 For up to date guides and more see support.magtarget.com Step 4: At four corners, (1) snap the device underneath the support features, (2) make sure that the audio cable is routed as direction shown:

7. ENCLOSURES VisualTarget LIGHTED ENCLOSURES 5 For up to date guides and more see support.magtarget.com Step 3: Plug in Audio Jack to the device.

22. 20 For up to date guides and more see support.magtarget.com BY VisualTarget Step 5: To get ready to install the VisualTarget enclosure, one or two of the M3 screw can be screwed into the top edge of the bracket for making one-person installation easier.

12. BY VisualTarget 10 For up to date guides and more see support.magtarget.com Note: Power up the device using the home button if it is in sleep mode. The power button can be accessed via a paper clip using the methods shown below. For iOS device (iPad): For Android device (Samsung):

30. 28 For up to date guides and more see support.magtarget.com BY VisualTarget Step 5: To get ready to install the VisualTarget enclosure, one or two of the M3 screw can be screwed into the top edge of the bracket for making one-person installation easier.

16. 14 For up to date guides and more see support.magtarget.com BY VisualTarget Step 4: Plug the RJ45 connector from the power source in the socket on VisualTarget electronics. Choose one of the three mounting options: rear-offset mount, side mount and surface mount, then follow the specific guide for the chosen mounting option.

23. PREFERRED MOUNTING METHODS SIDE-MOUNT 21 For up to date guides and more see support.magtarget.com Step 6: a. Plug in the PoE cable into the port in the back of the enclosure. b. Slide iPad enclosure assembly onto the bracket (enclosure not shown for clarity): c. Ensure the iPad is receiving power. If not check if the PoE port is activated. d. Insert the remaining M3 fasteners to secure the enclosure in place.

39. PREFERRED MOUNTING METHODS SURFACE MOUNT 37 For up to date guides and more see support.magtarget.com Lighted VisualTarget Enclosure is shown here, but other types of enclosures can be installed using the same methods. This complete the installation of the MagTarget VisualTarget enclosure (surface).

21. PREFERRED MOUNTING METHODS SIDE-MOUNT 19 For up to date guides and more see support.magtarget.com Step 4: If not already run through the mullion, run the PoE network cable. As shown on the picture below. Install the cover piece at the same time.

38. 36 For up to date guides and more see support.magtarget.com BY VisualTarget Step 4: a. Plug in the PoE cable into the port in the back of the enclosure. b. Slide iPad enclosure assembly onto the bracket (enclosure not shown for clarity). c. Ensure the iPad is receiving power. If not check if the PoE port is activated. d. Insert the remaining M3 fasteners to secure the enclosure in place.

42. 40 For up to date guides and more see support.magtarget.com BY VisualTarget Step 3: Place the bracket onto the glass, and add sticker to the other side of the glass inside the office for covering.

29. PREFERRED MOUNTING METHODS REAR-OFFSET 27 For up to date guides and more see support.magtarget.com Step 4: If not already run through the mullion, run the PoE network cable. As shown on the picture below. Install the cover piece at the same time.

36. 34 For up to date guides and more see support.magtarget.com BY VisualTarget The inner holes of the Surface Mount highlighted in green below are spaced to fit standard electrical outlet boxes used in North America. For a secure installation we recommend using additional fasteners in the additional holes provided.

20. 18 For up to date guides and more see support.magtarget.com BY VisualTarget Step 2: a. Drill pilot holes with a small diameter drill bit per the Drill Guide. b. Drill full size holes as per Drill Guide. c. Install M6 rivet nuts. (sold separately) Step 3: Bolt the bracket tightly into place using M6 screws.

28. 26 For up to date guides and more see support.magtarget.com BY VisualTarget Step 2: a. Drill pilot holes with a small diameter drill bit per the Drill Guide. b. Drill full size holes as per Drill Guide. c. Install M6 rivet nuts. (sold separately) Step 3: Bolt the bracket tightly into place using M6 screws.

31. PREFERRED MOUNTING METHODS REAR-OFFSET 29 For up to date guides and more see support.magtarget.com Step 6: a. Plug in the PoE cable into the port in the back of the enclosure. b. Slide iPad enclosure assembly onto the bracket (enclosure not shown for clarity) c. Ensure the iPad is receiving power. If not check if the PoE port is activated. d. Insert the remaining M3 fasteners to secure the enclosure in place.

35. PREFERRED MOUNTING METHODS SURFACE MOUNT 33 For up to date guides and more see support.magtarget.com INSTALLATION STEPS Step 1: Temporarily hold the Surface Mount at the desired location and height, and mark the selected holes. ***Check local regulation to see if any rules apply to the height of the enclosure. In the USA the Americans with Disability Act (ADA) asks for a maximum reach height of 48 inches***

9. Step 5: Install the front enclosure. ENCLOSURES VisualTarget LIGHTED ENCLOSURES 7 For up to date guides and more see support.magtarget.com

19. PREFERRED MOUNTING METHODS SIDE-MOUNT 17 For up to date guides and more see support.magtarget.com INSTALLATION STEPS Step 1: a. Download and print the Drill Guide from support.magtarget.com that correspond to the bracket purchased. Ensure the drill guide template is printed at full scale using the Actual Size option in Acrobat Reader*** b. Temporarily hold the Drill Guide on the desired location and height. Check local regulation to see if any rules apply to the height of the enclosure. In the USA the Americans with Disability Act (ADA) asks for a maximum reach height of 48 inches***

11. ENCLOSURES VisualTarget LIGHTED ENCLOSURES 9 For up to date guides and more see support.magtarget.com Step 6: Plug the RJ45 connector from the power source in the socket on VisualTarget electronics. Choose one of the three mounting options: rear-offset mount, side mount and surface mount, then follow the specific guide for the chosen mounting option.

27. INSTALLATION STEPS Step 1: a. Download and print the Drill Guide from support.magtarget.com that correspond to the bracket purchased. Ensure the drill guide template is printed at full scale using the Actual Size option in Acrobat Reader*** b. Temporarily hold the Drill Guide on the desired location and height. Check local regulation to see if any rules apply to the height of the enclosure. In the USA the Americans with Disability Act (ADA) asks for a maximum reach height of 48 inches*** PREFERRED MOUNTING METHODS REAR-OFFSET 25 For up to date guides and more see support.magtarget.com

41. PREFERRED MOUNTING METHODS GLASS MOUNT 39 For up to date guides and more see support.magtarget.com The instructions below highlight our recommended installation method when mounting the VisualTarget back bracket 273-0020 on the glasses. INSTALLATION STEPS Step 1: Use Alcohol Pad provided in the kit to wipe the glass as well as the back of the bracket before putting the VHB tapes on. Step 2: Add four pieces 3M VHB tapes onto the right places of the bracket.

5. ENCLOSURES VisualTarget LIGHTED ENCLOSURES 3 For up to date guides and more see support.magtarget.com The instructions below highlight our recommended installation method when installing VisualTarget Lighted Enclosures. INSTALLATION STEPS Step 1: Separate the back and front enclosures.

14. 12 For up to date guides and more see support.magtarget.com BY VisualTarget The instructions below highlight our recommended installation method when installing VisualTarget Slim Enclosures. INSTALLATION STEPS Step 1: Peel off the liner of 3M VHB tape. Step 2: Place the iPad onto the enclosure and plug the flat lightning cable into the iPad. Slide the iPad in place until the flat Lightning cable slide in its cutout and the iPad lays flat into the enclosure.

37. PREFERRED MOUNTING METHODS SURFACE MOUNT 35 For up to date guides and more see support.magtarget.com Step 2: Drill hole into mounting surface and install the bracket. Make sure to use fasteners which correspond with the type of mounting surface (use screw anchors if needed). Route the PoE cable through the center of the bracket and terminate cable at the same time. Step 3: To get ready to install the VisualTarget enclosure, one or two of the M3 screw can be screwed into the top edge of the bracket for making one-person installation easier.

15. Step 3: Fasten the provided M3 set-screw using a 1.5 mm Allen wrench. Note: the set-screw head should stop flush with the outside surface of the enclosure. Moving the set-screw all the way in would result in damage to the iPad. Note: Power up the iPad using the home button if it is in sleep mode. The power button can be accessed via a paper clip using the method shown below. Verify that the iPad is charging. If not ensure the PoE switch has been turned on for this particular location. ENCLOSURES VisualTarget SLIM ENCLOSURES 13 For up to date guides and more see support.magtarget.com

3. TABLE OF CONTENTS ENCLOSURES 2- 1 0 V isual T arget LIGHTED ENCLOSURES 1 11-14 V isual T arget SLIM ENCLOSURES REAR OFFSET MOUNT 2 23-30 4 31-37 SURFACE MOUNT 5 38-40 GLASS MOUNT 6 SIDE MOUNT 15-22 3 PREFERRED MOUNTING METHODS

Views

  • 693 Total Views
  • 619 Website Views
  • 74 Embeded Views

Actions

  • 0 Social Shares
  • 0 Likes
  • 0 Dislikes
  • 0 Comments

Share count

  • 0 Facebook
  • 0 Twitter
  • 0 LinkedIn
  • 0 Google+

Embeds 2

  • 12 magtarget.odoo.com
  • 2 support.magtarget.com